Green Guard Pms Relief

Persistent Activity: lvermax®(ivermectin) Pour-On has been proved to effectively control infections and to protect cattle from re-infection with: Oesophagostomum radiatum and Dictyocaulus viviparous for 28 days after treatment; Cooperia punctata and Trichostrongylus axei for 21 days after treatment; Ostertagia ostertagi, Haemonchus placei, Cooperia oncophora and Cooperia sumabada for 14 days after treatment; Damalinia bovis for 56 days after treatment.

Treatment of Cattle for Horn Flies: lvermax®(ivermectin) Pour-On controls horn flies (Haematobia irritans) for up to 28 days after dosing. For best results lvermax®(ivermectin) Pour-On should be part of a parasite control program for both internal and external parasites based on the epidemiology of these parasites. Consult your veterinarian or an entomologist for the most effective timing of applications.

Dosage: The dose rate is 1 ml for each 22 lb of body weight. The formulation should be applied along the topline in a narrow strip extending from the withers to the tail head.

Administration:Squeeze-Measure-Pour System (33.8 fl oz 1 Liter Bottle with 25 mL Measuring Cap)

Attach metering cap to the bottle.
Select the correct dose rate by rotating the adjuster cap in either direction to position the dose indicator to the appropriate dose.
Gently squeeze the bottle to fill to level (any excess will return to the bottle) and then tip and apply to animal along topline.

BackPack (84.5 fl oz/2.5 Liter Pack and 169 fl. oz/5 Liter Pack).

Connect the applicator gun to the backpack as follows: Attach the open end of the draw-off tubing to the dosing equipment. (Because of the solvents used in the formulation, only the Protector Drench Gun from Instrument Supplies Limited, or equivalent, is recommended. Other applicators may exhibit compatibility problems resulting in locking, incorrect dosage or leakage).

Replace the shipping cap with the draw-off cap and tighten down.

Attach draw-off tubing to the draw-off cap.

Gently prime the applicator gun, checking for leaks.

Follow the manufacturer's directions for adjusting the dose.

When the interval between uses of the applicator gun is expected to exceed 12 hours, disconnect the gun and draw-off tubing from the product container and empty the product from the gun and tubing back into the product container. To prevent removal of special lubricants from the Protector Drench Gun, the gun and tubing must not be washed.

Free standing (338 fl oz/10 Liter Bottle and 676 fl oz/20 Liter Bottle)

Connect the applicator gun to the Bottle as follows: Attach the open end of the draw-off tubing to the dosing equipment. (Because of the solvents used in the formulation, only the Protector Drench Gun from instrument Supply Limited, or equivalent is recommended. Other applicators may exhibit compatibility problems resulting in locking, incorrect dosage or leakage).

Replace the shipping cap with the draw-off cap and tighten down.

Attach draw-off tubing to the draw-off cap.

Gently prime the applicator gun, checking for leaks.

Follow the manufacturer's directions for adjusting the dose.

When the interval between uses of the applicator gun is expected to exceed 12 hours, disconnect the gun and draw-off tubing from the product container and empty the product from the gun and the tubing back into the product container. Replace the draw-off cap with the shipping cap. To prevent removal of special lubricants from the Protector Drench Gun, the gun and tubing must not be washed. If the shipping cap is to be used with the faucet spigot installed (which can be used for refilling the 33.8 fl oz/1 Liter Bottle, 84.5 fl oz/2.5 Liter Pack or 169 fl oz/5 Liter Pack), pop the plastic seal out of the center of the shipping cap, screw in the threaded spigot, and tighten down. Store the bottle upright, with the spigot in the off position between uses.